Throttle Body Spacer with blades – for Ford 4.0L V6s, L4s, as well as 4.6L and 5.4L Ford V8s
Original price was: $245.00.$214.00Current price is: $214.00.
Boost your Ford’s power and efficiency with Viser’s Throttle Body Spacer!
This simple upgrade enhances airflow for dramatic gains in torque, especially in the low and mid RPM range.
We did a comparative dyno on a 4.0 engine with 150,000 miles, and the blades added 13lb of torque at the mid range!
Before and after dyno attached.
The improvement increase feels more dramatic than the dyno shows because the extra power is available immediately!
20 in stock (can be backordered)
Boost your Ford engine's power with this easy-to-install throttle body spacer with blades.
Using technology from newer Ford plenums (with permission), the blades improve airflow quality which boosts low and mid range performance. This means better acceleration and a more responsive driving experience.
The 25mm spacer is made from durable black anodized aluminum and is carefully shaped to optimize airflow into your engine. It has all the necessary hardware, including longer bolts, for a straightforward installation.
This intake upgrade is legal for street use in most states, but it has not been reviewed by the California Air Resources Board (CARB). As such, it may not be legal in California and other states that have adopted California emissions standards. Please check your local regulations.
Overview
Increase in Performance and Efficiency
This bolt-on upgrade enhances your Ford engine's power, throttle response, and drivability. It can also improve fuel economy if you can keep your foot off the gas pedal!
Specifications
- Part Type: Intake Optimization: Bolt-on Upgrade
- Product Line: Viser Performance Intake Systems
- Engine Upgrade Type: Bolt-on (Hardware Included)
- Package Dimensions: 6" x 6" x 2"
- Part Category: Performance Parts
- Part Fitment: Direct Fit
- Shipping Weight: 3.00 lbs
- Vendor Part Number(s): Viser Throttle Body Spacer
Vehicle Fitment
Does the Viser Throttle Body Spacer Fit Your Vehicle?
- Engine:
- Ford V6 4.0L, 3.0L (Lincoln LS & Zephyr)
- Ford V8 4.6L, 5.4L
- Aspiration: Naturally Aspirated
- Make: Ford
- Model:
- 2005-2011 Crown Victoria
- 2005-2016 E-150, E-250, E-350
- 2004-2010 Explorer
- 2007-2010 Explorer Sport Trac
- 2002-2006 F150
- 2003-2005 Lincoln LS
- 2004-2011 Lincoln Town Car
- 2005-2011 Mercury Grand Marquis
- 2004-2010 Mercury Mountaineer
- 2005-2010 Mustang (4.0 Only)
- 2006 Lincoln Zephyr
Additional information
| Weight | .5 kg |
|---|---|
| Dimensions | 5 × 5 × 1 cm |
John –
I’ve got a 2005 Mustang 4.0 with about 92,000 miles. Other mods I’ve got installed are a Ford Racing Cold Air Intake, Flow tech headers, and Flow master Dual Exhaust. It was a very simple install, took about 30 minutes. Had some carb and throttle body cleaner to clean the throttle body while it was apart. I’m really happy with the results. Noticed a difference in the acceleration, and it got rid of the stumble when I get on it. Definitely pulls much better at the 25-35 mph mark. So far, I’m seeing improved gas mileage, but haven’t driven a lot to see the full impact. Would definitely recommend to anyone looking to get a little more out of their Mustang 4.0.
Anthony Castelli –
Dyno tested this spacer on a BONE STOCK 4.0 Mustang. Not only did it make slightly more power through the entire power band, we picked up 10ftlbs in the lower RPM. Awesome product, truly makes a difference!